Home
Duane
Linda
BMW articles
Czech Students
Search my web
Ji-young's travel

BMW motorcycle compression testing

by Duane Ausherman


Knowing the compression of a cylinder is one of the most important things.  Poor compression will reduce the hp output, top speed, acceleration, fuel economy and make the carb mixture harder to adjust.

There are a few ways to check compression in an engine.

  1. Use a gauge that seals by being shoved into the spark plug hole.  Very poor and not worth doing.
  2. A screw in connector on a short piece of hose.  Then plug a gauge into the hose.  This is far better and probably the most common way.
  3. A "leak down" test is the best way.  It is the standard of the aircraft industry.  This puts pressure into the spark plug hole and one can measure how much leaks out.  One may also listen for where it is leaking and learn if it is rings or valves and which valve.

The first thing I always do is to slowly kick it through and "feel" the compression.  With some experience, one can learn to guess the compression quite accurately.  At the minimum you should be able to feel if they are equal and if one is lower, which one it is.

I am most familiar with the second method and will describe it.  The engine must be warmed up to get an accurate result.   When removing a spark plug always make sure that there is no dirt or crud at the base of the plug.  Loose dirt may cause real trouble.  Many mechanics use a blast of air to clean out the area.  That just isn't always good enough.  The air blast may not break all of the crud loose.  I prefer to break the spark plug loose a 1/2 turn and then blast it with air.

I like to remove both plugs on a BMW twin.  Screw in the hose on the cylinder to be tested.  Give it a few slow kicks to feel the cylinder when it is on compression and the one that has none.  Lay the gauge head where you can observe it easily.  Open the throttle completely.  That allows maximum air to get into the cylinder for compression.  Failure to have it open will give false results.  All human errors in measurement will give a low reading.  I have seen engines torn down just because someone failed to correctly measure the compression.

Bring the kick start lever up to compression and lift the lever up to the top.  Now give it one healthy kick and observe the number.  Is the needle moving down quickly or staying right there?  That number should be about 1/2 of the total that you reach.  Now give it the second kick and note the number.  A third, forth, fifth and sixth kick.  If you arrived at a total of 125 psi.  note that too.  Here is how it should have looked.

  1. 60 psi
  2. 90 psi
  3. 105 psi
  4. 113 psi
  5. 118 psi
  6. 120 psi

The first kick produced about 1/2 of what the total turned out to be.  Each successive kick produced almost 1/2 of that number.  The first was 60, so add in 30 more and get 90, now add in 15 more and get to 105, but you get the idea.

Below is an example of a poor cylinder.

  1. 25-35 psi
  2. 45-55 psi
  3. 65-75 psi
  4. 85-95 psi
  5. 100-110 psi
  6. 120-130 psi

This time each kick produced about the same increase.  The first produced about 30 and each one after that did almost as good.  Towards the end it would diminish a bit and only add maybe 10-15.  You would have the feeling that it should get kicked many more times to finally "get there." 

The kicks should be made in quick succession.  The amount of "leakage" between each kick can mean a leaky hose or valve.  That is what is so nice about the leak down test and why it is the standard in piston aircraft.

How much for each type engine in healthy condition?

R50-R50/2  120-140 psi
R60-R60/2  125-145 psi
R69S          150-185 psi

Compression tests on the /5 and later

The /5 and later usually have an electric starter.  This does not mean that because it is easy to crank over, you should just crank until it reaches maximum.  We still restricted the test to 6 compression strokes and carefully watched the gauge as it "stepped up" on each stroke.

The CV carbs must be removed a bit to get air in easily.  The older slide type carbs on the R50/5 and R60/6/6 and /7 should just have the throttle opened up fully during the testing.

Tuning evidence

As the compression gets lower and lower, the tuning changes in the engine.  An experienced tuner will "feel" this as the carb adjustments are made.  It just won't respond to the idle air adjustments properly.  The sound out of the exhaust just isn't crisp either.

R51/3, R67, R67/2, R67/3, R50 and R60 tuning

When the compression gets down to around 100 - 105 psi, the carbs won't respond well to adjustments.  The bike will still start easily.  The top speed will be reduced by 10-15 mph, but how many "open it up" to find out?  At 75-80 psi, the bike will still start, but not pull out without some warm up time.  It may take a lot of "tickling" to get enough gas into it to keep running.  It will be really sluggish at medium highway speeds.  The carb tuning will be rather flat too.  At 50 psi and lower it will be really hard to start and barely keep up with traffic on the highway.  The gas mileage will suffer badly too.  On the R50 it is not so accurate as it is hard to get much resistance from a good engine.  This description applies to the singles too.  They are not "sport" tuned.

R68, R69, R69S and R50S tuning

The R69 might be a few psi lower, but is nearly as high as the other sport models.  These models are easy to test by foot.  With my weight of 175, as the kick starter goes through the compression stroke, my whole weight will be on the lever.  My other foot will be off of the ground for a second.  It will slowly sink through the compression stroke.  That is good compression.  The R68 has a different transmission and feels easier to kick.  By going through compression several times, one can easily feel which cylinder is low and about how much it is.  After you have a lot of experience with feeling the resistance, this "kick method" will allow one to get within 10 psi of what the gauge will show. 

At around 125-130 psi it starts to be a bit harder to adjust the idle air, but will still start easily.  At 90-100 psi it will start, but not so easily and take some warm up time.  The carbs just won't respond well at all.  At 75-80 psi, the bike will still go well on the highway, but top speed is down at least 25 mph.  But the R69S is a 110 mph bike, so the limit of 80 mph isn't something that many owners test.

General info

An engine with a sport cam may not show these results.  The valve overlap can affect the measurement at cranking rpm.  It may give an artificially low reading.

At cranking, or kicking, speeds the valves are operating under ideal conditions.  They operate so slowly that they can fully seat, while at road rpm they may wobble and chatter in the loose valve guides.

When we had a head off of the bike, we would put some solvent into the intake port and exhaust port.  If the liquid leaked through into the combustion chamber just sitting, think about how it may leak in a dynamic test.

I saw a BMW engine with very low compression of 25-30 psi in each side still go down the freeway at almost 60 mph, but that was about all it would produce and it had to warm up to even get there.  That particular motorcycle lived on top of a hill and the owner would use the entire hill to "bump start" it.  It got so bad that even after a couple of blocks of that type of running it wasn't running well at the bottom, so he brought it in so I could "tune it up" and fix everything.  The valves were completely burned up and solvent ran through them instantly.

A carb that has a partially blocked idle gas jet would produce a "flat spot" on an otherwise good engine.  On one with lower compression, it is harder to "feel" the flat spot.  The entire performance is reduced and the whole response is flat anyway. 

 

More BMW motorcycle information

My homepage

To keep this webpage free for all to use, please consider a donation, thanks

This page was last edited: 02/03/2006 - copyright Duane Ausherman
Web hosting provided by hostmeister.com