BMW articles
Czech Students
Search my web
Ji-young's travel

BMW motorcycle petcocks, Everbest, Karcoma, Germa and fuel flow

By Duane Ausherman

This page is about the BMW motorcycle models between 1955 and about the early 80s. 

This Everbest petcock was used on BMW motorcycles from about 1956 through 1973.

The Everbest petcock and its standard BMW tool to install/remove it.  The fuel filter is missing in this photograph.   

The Everbest petcocks used on BMW motorcycles, were a bit odd to use.  They didn't follow the United States standard for valves and petcocks.  The text embossed in the castings are in German, not English.  This petcock was used from the first of the Earles fork models until the end of the /5 BMW series in 1973.  Both of the original tanks on the /2 BMW motorcycle used only one petcock.  All tanks on the /5, /6 and /7 had two petcocks.  The reason to use both is explained below. 

This shows the Everbest petcock in the "off" position.

The "off" position.  See the "ZU" showing?

This is the "on" position for the Everbest petcocks used on BMW motorcycles.

The "on" position with the "A" showing. 

This is the "reserve" position for the Everbest petcock used on BMW motorcycles.

The "reserve" position with the "R" on the top of the indicator?

This photo is to show the Everbest petcock totally disassembled.

The Everbest petcock totally disassembled.  This photo shows black gaskets, not the typical red ones.  Thanks to Brian Rozema for the photo. 

You can see the crimp that holds the Everbest petcock together.

This shows the crimp that must be "opened up" to get the barrel out and later "recrimped" and you can see why it can be rebuilt a limited number of times. 

This photo shows the red Everbest gasket as compared to a dime.

This is the original hard red gasket used to seal the petcock to protect from leaking fuel.  If it leaks, see below. 

The main and reserve tubes

        This shows the size of the tubes on an Everbest petcock that protrude up into the fuel.

You may find some variation from those figures.  This is a NOS Everbest fuel petcock from late 55 to the early 70's.  See the bend in the main tank stand tube? That is to have the opening of the tube at an angle.  On the small 4 1/2 gallon tank, the tube impinges upon bottom of the side tool box so badly that the tube opening would get blocked.  I have removed many petcocks to find the brass tube mashed over to cover some part of the opening.  My solution was to cut a tiny bit off at an  angle.  That will result in a slightly smaller reserve capacity, but allow full fuel flow during main tank operation.  This is critical on the R60/2, as it was prone to piston seizure and this was one factor described by BMW.  I think that there was a service bulletin on this issue. 

Do not cut the lower tube down to increase the amount of fuel on reserve.  That tube sticks up in the fuel a bit to try to stay above any water or dirt. 

Everbest fuel filters

The petcocks come with a fuel filter built in.  The filter is quite good, but is delicate and needs very careful treatment.  The very early ones had a small mesh screen that was easily distorted.  Handle with care. 

The Everbest petcock fuel filter  The Everbest petcock fuel filter is shown mounted.

The oldest style /2 filter in the Everbest petcock and what it looks like when removed.  Photos by Marc, thanks.  I don't remember when they changed the type of filter screen.   

petcock9.jpg (13444 bytes)

The later style screen fuel filter for the /5 BMW motorcycle.  Photo by Jeff Kuzmanoff, thanks. 

That screen should be examined and cleaned every few thousand miles.  Be very careful with it as it is quite delicate.  Get a new one for a spare as you will use it eventually. 

The Everbest was never a good petcock and usually leaked within a year or two of purchase.  The leak would be around the barrel and through the cork gasket that was supposed to seal it up.  I understand that it can be rebuilt once, maybe twice, with some degree of success.  I have never done this and have heard of mixed results.  Go to the well written article at http://members.aol.com/vechbmw/petcock.html for more info.  BMW finally upgraded to the Karcoma petcock in 1974 for the /6 series.  It is far better and is often used for the older models too.  It is a direct swap. 

We always wondered how BMW could use such a poor item on a motorcycle for so many years.  At a service school put on by a factory instructor, I asked that question.  He laughed and told us that there is a "story" behind it.  Up to that time, (mid 50's) no decent system for breathing a gas tank had been developed.  A BMW engineer had invented a method for the tank to not need venting at the gas cap.  The fuel petcock would allow a lot of tiny bubbles of air to go upwards in the fuel as it was flowing down.  BMW patented it and licensed it to Everbest.  They were so proud of the invention that they somehow have over looked the fact that in all other aspects of petcock requirements, it was a failure.  Even the previous petcocks on the early /3 were better for sealing gas. 

Suggestion for /2 BMW motorcycle restorers

If you want to have an original petcock on your /2 restoration, I suggest using a Karcoma for actual riding.  For serious Concours D'Elegance judging I suggest draining the tank and installing the Everbest.  If the bike won't be started up, then you won't need to worry about your old Everbest leaking, especially if the tank is empty anyway.  If you have located a good Everbest, then it will soon leak if you add fuel.   

The Karcoma petcock on the /6 BMW motorcycle

In 1974, when BMW came out with the /6 models, they also introduced a decent petcock.  It is made by a company named Karcoma and it works well.  It is easily rebuilt, but seldom needs it.  Many owners are now forced to use the Karcoma due to the lack of supply of the older "original" Everbest.  Later on, BMW used a Karcoma that had an angled fuel line connection and they are harder to hook up with fuel line.

The three positions of a Karcoma petcock for BMW Motorcycles

A Karcoma petcock in the off position.

This is the "off" position.  It would also be "off" if the arm was pointed to the left, as both positions are equal.  This petcock is the older type with the "straight down" connector.

This photo shows the Karcoma petcock in the "main tank" position.

This is the "on" position.  This is the later petcock with the angled connector.

This photo shows the Karcoma petcock in the "reserve" position.

This is the "reserve" position.


The Karcoma petcock for the /6 BMW motorcycles can be easily opened up, but not so easily put back together again.  Once open, it can be cleaned up and that will usually fix any actual petcock leak.  Just remove the plastic cover and then unscrew the cover plate to get it apart.  Be very careful.  Some use a bit of Vasoline on the black rubber piece to allow tightening of the cover and still allow the hand lever easy movement. 

Germa petcock

The Germa petcock is similar to the Karcoma.   This shows the hand lever removed from a Germa petcock.

The Germa petcock was almost identical to the Karcoma, but the hand lever was removable by removing the screw.  Thanks to Steve D.  for the photos. 

Fuel leaks at the petcock threads

Upon installing a petcock you may find that it leaks at the threads.  Don't use teflon tape or any type of sealer on the threads.  That is the wrong way to do it.  It is harder and probably won't work.  It is easy for one to think of the threads as in a plumbing connection.  That would be incorrect.  The seal is at the reddish hard gasket (see above) that goes between the petcock and the tank.  Carefully inspect the matching metal surfaces of the tank and top of the petcock for any type of defect.  Sand or file to make it a perfectly smooth surface.  Use only a proper wrench to tighten up that nut.  That nut is quite special.  It has right hand threads on the top at the tank.  It has left hand threads on the bottom where it threads onto the petcock.  It is similar to a turnbuckle in that respect.  Tightening up the nut will simultaneously pull the petcock and tank together against the hard gasket.  Hold the petcock in position and start the threads at both ends at the same time.  Then continue to hold the petcock and tighten the nut.  It must be fairly tight to seal.  The hard gasket can be reused, but check it for smoothness.  All four surfaces must be smooth and clean. 

One or two petcocks?

Why you should use both petcocks on models that have two petcocks.  It is very important to use both petcocks for riding that requires a high fuel flow.  What is a high flow ride?

1.  Running above 100 mph

2.  Two up with a full fairing at 80 mph or so. 

3.  At 80 mph into a headwind of 20 and we are back into #1 above.   

The R75 should run with both petcocks open.  When the tank is low and the load is high, you can get into trouble.  I can tell you that our race bike had this problem.  It was light, with a small rider and no wind so the load wasn't heavy.  The state of engine tune was medium.  The petcocks weren't clogged.  Normally it would go about 125 mph.  One day before a race, with both petcocks on and the tank low, but not on reserve yet, it wouldn't go above 115 mph. Adding fuel solved this problem.  This translates to a very marginal fuel delivery system for a stock bike with sizable load at a high speed.  In this case, the petcock was operating as the main jet, not good.

Think about this when you have a serious load and adjust accordingly.  Don't assume that you have full fuel flow, unless you have measured it a few minutes earlier.  The stock filters can clog up very quickly.  If you put accessory filters in the line too, this is additional restriction.  I don't recommend them.  That means LESS FLOW.  I don't ever run on one petcock at over 60 mph.  Don't run low if you have a serious load on the engine.  Top ends have burned up by running out of gas.  On the /2, it was common for the piston to get so hot that it blew a hole in the top.  We call that a "holed piston" and the parts that blow down into the lower end can get into the lower end and ruin the crank.  The owner could replace the top end and think all is well, but a few thousand miles later the lower end shows symptoms of failure. 

BMW motorcycle fuel flow tests

This shows the fuel flow test being performed on a BMW motorcycle.


It is a good idea to measure the number of seconds that it takes to fill a fixed volume container from each petcock.  Record it for future comparison.  An Everbest will flow 100 cc of fuel in about 12-15 seconds with a half full tank.  Only when it would get up to around 20 seconds would I remove the petcock to investigate it further.  A full tank will flow more fuel than a low one, so take that into account in your flow measurements.

Notice the appearance of normal flow, as you need to be able to recognize it.   Later when you have some high speed problem, you will be able to easily check to see if it is fuel flow related.  If you pull the fuel line off often and let the fuel flow freely, you will eventually learn to see what is "normal" and what is "too little". 

If you think that you may be seeing less fuel flow than you want, here is a quick test.  Remove the lower end of the fuel line at the petcock that you want to check.  Use air pressure to try to blow any dirt upwards and back into the fuel tank.  Be sure to clean out both main and reserve positions.  Now test the flow again.  If it has improved, then you have just proven that the fuel flow system was clogged up.  You haven't fixed anything at all, only temporarily relieved it.  This might get you home, but you must drain and clean the entire fuel system soon. 

Other /2 BMW motorcycle fuel flow problems

The crossover tends to collect a lot of foreign material.

This crossover was almost completely clogged up.  This shows only some of the dirt. 

This is the dirt that came out of a crossover on a slash two BMW motorcycle.

The dirt that came out of a tank into a large dish pan.  This will kill a /2 top end. 

The /2 BMW has a crossover line directly between the two sides of the tank.  The /5 BMW and later have this crossover below the petcocks.  The later system is far better.  The /2 crossover tube can get clogged up partially or completely.  The connecting tubes for the crossover line are at the rear and about the lowest place in the fuel.  That tube collects the trash.  One can peer into the tank to check fuel level and happen to check the right side.  It will be fairly full, but the bike is actually out of gas, or the top speed may be limited.  This is because the left side is empty and the crossover is clogged.  This is very risky because by the time that you find that top speed is limited, it may have already overheated the engine.  It is best to remove the crossover from time to time and make sure it is clean.  The crossover tube is far less likely to leak than the other two lines and therefore it gets less attention.  Replace it when you replace the other fuel lines.  Carry, as a spare part, a piece of the fuel line that is pre-measured to replace the longest one that your model uses.  It is easy to shorten it if needed, but it is already correct for the longest one.  It also may serve as a test piece. 

The /2 BMW motorcycle on reserve. 

When on reserve, the fuel pressure from gravity is less.  If the crossover is clogged at all, then the left side will run out first.  Now you have another reason for a lower fuel flow: and that is that the fuel on the right side must pass through a partially clogged up fuel line and then into the petcock.  You may have tested the fuel flow on reserve, but that doesn't test the crossover line.  Going on reserve should signal you that you may need to reduce speed.  

Aftermarket fuel filters

Finding the tank liner paint flaking off and getting caught in the filters and possibly in the float needle valve can make one consider an inline fuel filter.   I suggest checking the fuel flow above the filter and below it.   I have measured many of these filters over the years and some restrict as much as 50%.   Don't use them.   I recently measured one that had about 90% flow and that is acceptable. 

It has come to my attention that many modern fuel filters don't restrict fuel flow by much at all.  In that case, I too would use them.

More BMW motorcycle information

My homepage

To keep this webpage free for all to use, please consider a donation, thanks

This page was last edited: 07/20/2006 - copyright Duane Ausherman
Web hosting provided by hostmeister.com